XRAY: DIFF GASKET (4)
This is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsThis is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsSuspension pivot pins, hardened for very high durability and long life, polished for smooth operation. Used on inboard pivot point of XB4 suspensio...
View full detailsThreaded 4.9mm ball end with 5mm thread length for connection to molded ball joints. Set of 2.
Threaded 4.9mm ball end with 10mm thread length for connection to molded ball joints. Set of 2.
Rear wing for XB2/XB4 made from thick 1.0mm Lexan™ material is highly reliable with less chance of breakage, giving higher traction & stability...
View full detailsXB4 Gamma 4D body is designed especially for low traction tracks. The profile of the body improves the stability and increases downforce towards th...
View full detailsThe springs have been specifically designed to complement the big bore shocks. Set of 2.The spring rate of the linear springs is constant during th...
View full detailsMolded composite C-hub for steering block. Caster pre-set at 6°. The roll center position can be easily and quickly adjusted by inserting different...
View full detailsHigh-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 10x15x4. Top-quality professional ball-bearings for a super-fr...
View full detailsOptional springs specifically designed to complement the big-bore shocks. These springs are softer than the 1 dot springs. The spring rate is const...
View full detailsEccentric bushings for adjusting suspension settings, made from tough composite. Fits alu and composite multi-adjustable rear uprights. Two sets of...
View full detailsRear wing holder molded from tough composite material.
Gear differential precision internal gears made from tough composite material. Includes 2 bevel gears and 4 satellite gears. Also fit NT1 gear diff...
View full detailsSet of composite shims for mounting servos to mounting posts. Includes: 3x6x1mm (qty 4), 3x6x2mm (qty 4), 3x6x3mm (qty 4).
Molded composite C-hub for steering block. Caster pre-set at 6°. The roll center position can be easily and quickly adjusted by inserting different...
View full detailsNew optional FRONT linear springs are recommended for high-traction tracks. The springs have been specifically designed to complement the big-bore ...
View full detailsThe springs have been specifically designed to complement the big bore shocks. The spring rate is constant during the entire spring compression.The...
View full detailsSpring steel anti-roll bar, 2.0mm thick. This optional anti-roll bar offers different anti-roll stiffness adjustment so that you can fine-tune the ...
View full detailsSpring steel anti-roll bar, 1.8mm thick. Marked with 8 laser-engraved lines for easy identification. This optional anti-roll bar offerw different a...
View full detailsThe springs have been specifically designed to complement the big bore shocks. Set of 2.The spring rate of the linear springs is constant during th...
View full detailsThe springs have been specifically designed to complement the big bore shocks. The spring rate is constant during the entire spring compression.The...
View full detailsHARD molded composite C-hub for LEFT steering block. Made from super-tough, high-tech composite material. Caster pre-set at 9°. For use with matchi...
View full detailsCNC-machined CVD drive shaft coupling. Made from world-renowned Hudy Spring Steel™. Specially hand-ground for maximum precision.
Rubber O-ring 1.5mm thick x 14mm dia. Set of 10 pieces.