

XRAY: Composite Spur Gear H 84T / 48P - Orange
XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. Product released: 3rd...
View full detailsLow-friction 3.5mm drive pin clips for protecting and cushioning drive shaft pin in diff outdrives. Made from all-new, extra-strong composite mixt...
View full detailsMolded composite steering block of “hard” hardness (H) for foam-tire racing. The steering block features two Ackermann positions, and uses small b...
View full detailsThis is a replacement XRAY X-Stiff Composite Servo Saver Set, and is intended for use with the XRAY T3'11, T3’12, XII, X12 and X10 Link vehicles. T...
View full detailsSet of two adjustable turnbuckle for adjusting camber of rear uprights, manufactured from world-renowned top-secret "Hudy Spring Steel". Product r...
View full detailsMolded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3, T4, RX8, XB8, NT1, X1 and GT...
View full detailsOptional specially-modified high-performance Kevlar®-reinforced 513mm-long, 3mm-wide front drive belt.This belt is very thin and elastic as possib...
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsSet of two adjustable steering rod turnbuckles, manufactured from world-renowned top-secret "Hudy Spring Steel". Product released: 4th July 2002
Optional specially-modified high-performance Kevlar®-reinforced 189mm-long, 3mm-wide rear drive belt.This belt is very thin and elastic as possible...
View full detailsOptional specially-modified high-performance Kevlar®-reinforced 351mm-long, 3mm-wide drive belt.This belt is very thin and elastic as possible for...
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsComplete gear differential set for XRAY T3 includes composite differential case and cover with pulley. Differential gears are made from tough compo...
View full detailsThis is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsThreaded 4.9mm ball end with 8mm thread length for connection to molded ball joints. Set of 2.
Molded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crashes....
View full detailsNarrow high-performance pinion gear manufactured from special lightweight aircraft duraluminum is 1.5mm thinner and 25% lighter than the regular-s...
View full detailsMolded composite front lower suspension arm made from hard material. 2mm longer to better fit new suspension mounts. Fits T4’14. After extensive te...
View full detailsLower inner pivot pins for XRAY T4’14 onwards. Hardened for extra-high durability and long life. Set of 2.
Silicone O-ring fits over 24mm shaft. 0.7mm thick. Set of 10 pieces.
Precision-molded 20T layshaft pulleys for XRAY T2’008, T2'009 and T3 includes composite shims. Standard pulleys for XRAY T2’008, T2'009, T3 US Foa...
View full detailsEccentric bushings for adjusting suspension settings, made from tough composite. Fits XB4 alu suspension holders. Using eccentric suspension bushi...
View full detailsThis is a replacement XRAY 20 Tooth Low Friction Fixed Pulley.
We will send you a notification as soon as this product is available again.
We don't share your email with anybody