XRAY: SPUR GEAR "H" 84T / 48 - ORANGE
XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsMolded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3, T4, RX8, XB8, NT1, X1 and GTX8
This is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsMolded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crashes....
View full detailsEccentric bushings for adjusting suspension settings, made from tough composite. Fits XB4 alu suspension holders. Using eccentric suspension bushi...
View full detailsPolished chrome pin. Dia. x length = 2mm x 9.8mm. Set of 10 pieces.
Precision-machined bushing for front C-hub steering block pivot screws on XRAY T2, T3. Includes 4 pieces: 2 short + 2 long.
Precision-molded 20T layshaft pulleys for XRAY T2’008, T2'009 and T3 includes composite shims. Standard pulleys for XRAY T2’008, T2'009, T3 US Foa...
View full detailsNarrow high-performance pinion gear manufactured from special lightweight aircraft duraluminum is 1.5mm thinner and 25% lighter than the regular-s...
View full detailsPrecision-molded 20T layshaft pulley made of specially-formulated graphite composite material that is a perfect balance of reliability and perform...
View full detailsThreaded 4.9mm ball end with 5mm thread length for connection to molded ball joints. Set of 2.
Silicone O-ring fits over 24mm shaft. 0.7mm thick. Set of 10 pieces.
Threaded 4.9mm ball end with 10mm thread length for connection to molded ball joints. Set of 2.
XRAY precision molded offset spur gear 81 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass.
Molded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crash...
View full detailsPolished chrome pin for ECS drive shaft, 2.0 x 9.0mm. Specially hand-ground for maximum precision. To help prevent of loosening of the setscrew fr...
View full detailsNarrow high-performance pinion gear manufactured from special lightweight aircraft duraluminum is 1.5mm thinner and 25% lighter than the regular-s...
View full detailsMolded composite rear lower suspension arm made from hard material. Fits T4’14.After extensive testing of many different composite mixtures, the fa...
View full detailsSet of two adjustable turnbuckle for adjusting camber of rear uprights, manufactured from world-renowned top-secret "Hudy Spring Steel". Product r...
View full detailsRear lower outer pivot pins for XRAY T2, T3. Hardened for very high durability and long life. Set of two.
Linear 4S springs marked 2.8. The 4S springs have been specifically designed to complement the SLP shocks and are 20mm long. Set of 2.The 4S sprin...
View full detailsAlu shims 3x6mm size, 4mm thick, set of 10. Available in Black & Silver
High-speed ball-bearings manufactured specially for XRAY. ID x OD x thickness (mm) = 10x15x4. Top-quality professional ball-bearings for a super-fr...
View full details