XRAY: SPUR GEAR "H" 84T / 48 - ORANGE
XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsMolded composite servo saver set - extra stiff. Consists of 4 springs to make the servo saver strong enough to prevent extreme steering deflection ...
View full detailsLow-friction 3.5mm drive pin clips for protecting and cushioning drive shaft pin in diff outdrives. Made from all-new, extra-strong composite mixt...
View full detailsOptional specially-modified high-performance Kevlar®-reinforced 513mm-long, 3mm-wide front drive belt.This belt is very thin and elastic as possib...
View full detailsMolded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3, T4, RX8, XB8, NT1, X1 and GTX8
Optional specially-modified high-performance Kevlar®-reinforced 189mm-long, 3mm-wide rear drive belt.This belt is very thin and elastic as possible...
View full detailsThis is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsMolded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crashes....
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsPolished chrome pin. Dia. x length = 2mm x 9.8mm. Set of 10 pieces.
Precision-molded 20T layshaft pulleys for XRAY T2’008, T2'009 and T3 includes composite shims. Standard pulleys for XRAY T2’008, T2'009, T3 US Foa...
View full detailsNarrow high-performance pinion gear manufactured from special lightweight aircraft duraluminum is 1.5mm thinner and 25% lighter than the regular-s...
View full detailsPrecision-molded 20T layshaft pulley made of specially-formulated graphite composite material that is a perfect balance of reliability and perform...
View full detailsSilicone O-ring fits over 24mm shaft. 0.7mm thick. Set of 10 pieces.
Specially-modified high-performance 513mm-long and 3mm-wide front drive belt comes standard in XRAY T2’009 Rubber-Spec Conversion Set - 38T Pulley....
View full detailsPolished chrome pin for ECS drive shaft, 2.0 x 9.0mm. Specially hand-ground for maximum precision. To help prevent of loosening of the setscrew fr...
View full detailsNarrow high-performance pinion gear manufactured from special lightweight aircraft duraluminum is 1.5mm thinner and 25% lighter than the regular-s...
View full detailsRear lower outer pivot pins for XRAY T2, T3. Hardened for very high durability and long life. Set of two.
Set of two adjustable turnbuckle for adjusting camber of rear uprights, manufactured from world-renowned top-secret "Hudy Spring Steel". Product r...
View full detailsXRAY precision molded offset spur gear 81 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass.
XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. Product released: 3rd...
View full detailsCarbide balls 2.4mm for ball differential. Improved, smoother diff operation over standard steel diff balls. These carbide balls are much harder th...
View full details