XRAY: SPUR GEAR "H" 84T / 48 - ORANGE
XRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been made from special hard composite material, strategically lightened to ...
View full detailsXRAY precision molded spur gear 84 tooth, 48 pitch. This spur gear has been strategically lightened to reduce rotating mass. Product released: 3rd...
View full detailsSST Rally 24/25 - yellow pair If you would like your tyres professionally glued, please click here Thus item is due to ship 29th May 2023
Pair of 26mm D-Window style Stockcar wheel. Produced in New Zealand to MRC design specifications, these wheels are built to take the beating of co...
View full detailsYelbow moulded 1/10 Touring Car wheel insert
Molded composite servo saver set - extra stiff. Consists of 4 springs to make the servo saver strong enough to prevent extreme steering deflection ...
View full detailsLow-friction 3.5mm drive pin clips for protecting and cushioning drive shaft pin in diff outdrives. Made from all-new, extra-strong composite mixt...
View full detailsSST Rally 24/25 - white compound pair If you would like your tyres professionally glued, please click here
Optional specially-modified high-performance Kevlar®-reinforced 351mm-long, 3mm-wide drive belt.This belt is very thin and elastic as possible for...
View full detailsMedium red moulded insert as used at the IFMAR Worlds 2012
Optional specially-modified high-performance Kevlar®-reinforced 513mm-long, 3mm-wide front drive belt.This belt is very thin and elastic as possib...
View full detailsMolded composite 4.9mm ball joints, open on both sides, for connection to 4.9mm ball. Set of eight. Fits XRAY T2, T3, T4, RX8, XB8, NT1, X1 and GTX8
Optional specially-modified high-performance Kevlar®-reinforced 189mm-long, 3mm-wide rear drive belt.This belt is very thin and elastic as possible...
View full detailsThis is a pack of four replacement XRAY Differential Gaskets, and is intended for use with the XRAY T3 family of 1/10 touring cars equipped with th...
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsMolded-composite rear upright features built-in 0° of outboard toe to improve traction and prevent suspension geometry changes in serious crashes....
View full detailsMolded composite C-hub for right steering block of T2, T3. Caster pre-set at 4°. Medium rigidity for rubber-tire racing. Use with matching left-si...
View full detailsComplete gear differential set for XRAY T3 includes composite differential case and cover with pulley. Differential gears are made from tough compo...
View full detailsEccentric bushings for adjusting suspension settings, made from tough composite. Fits XB4 alu suspension holders. Using eccentric suspension bushi...
View full detailsPolished chrome pin. Dia. x length = 2mm x 9.8mm. Set of 10 pieces.
Precision-molded 20T layshaft pulleys for XRAY T2’008, T2'009 and T3 includes composite shims. Standard pulleys for XRAY T2’008, T2'009, T3 US Foa...
View full detailsNarrow high-performance pinion gear manufactured from special lightweight aircraft duraluminum is 1.5mm thinner and 25% lighter than the regular-s...
View full detailsPrecision-molded 20T layshaft pulley made of specially-formulated graphite composite material that is a perfect balance of reliability and perform...
View full detailsThreaded 4.9mm ball end with 5mm thread length for connection to molded ball joints. Set of 2.